Skip to content
English
  • There are no suggestions because the search field is empty.

Equipment and Reading Sheets

 What is a Reading Sheet?

A reading sheet (also called an equipment log or daily log) is where operators record measurements and operational data for a piece of equipment — things like pressures, temperatures, fluid levels, runtime hours, and any other values your organization tracks for that unit. Reading sheets are the primary way equipment operational data is captured in EZ Ops.

Key point: Reading sheets are configured by your administrator for each piece of equipment. The rows you see, the units, and any auto-calculated values are all set up to match what your organization needs to track. Contact your administrator if a reading or row is missing.

Why Reading Sheets Matter

  • Equipment health tracking — daily readings give supervisors and operators an ongoing record of how equipment is performing
  • Schedule accuracy — total hours rows on reading sheets drive preventative maintenance schedules; accurate runtime logging means schedules trigger at the right time
  • Automated alerts — values that go out of manufacturer-specified ranges automatically notify the plant foreman
  • Calculated values — EZ Ops can perform math automatically based on your entries, reducing manual calculations and errors
  • Regulatory and compliance records — exported reading sheet data provides a timestamped history of equipment operation

How to Start a Reading Sheet Log

If Your Plant Has Shifts Enabled

  1. Navigate to the plant and open the EZ-Nav
  2. Go to Reading Sheets (sometimes labelled Equipment Logs)
  3. Select your shift — AM or PM — before starting
  4. Click Start Log on the equipment you are logging

If Your Plant Does Not Have Shifts

  1. Navigate to the plant and open the EZ-Nav
  2. Go to Reading Sheets
  3. Click Start Log on the desired equipment

The shift requirement is set by your administrator on the plant configuration. If you do not see a shift selection, your plant does not use shifts.

Entering Readings

Once you have started a log:

  1. Work through each row — enter the measured value for each row in sequence
  2. Numeric rows — enter numbers only; the unit is shown next to the row label (kPa, °C, L/min, etc.)
  3. Text rows — some rows allow text entry (e.g., notes or downtime codes); these will have a text input instead of a number field
  4. Dropdown rows — some rows present a list of options to choose from rather than a free-entry field
  5. Calculated rows — some values fill in automatically once you have entered enough other values. Do not try to manually enter calculated values if they appear locked or read-only

Section Breaks

Reading sheets may be divided into labelled sections (e.g., "Engine Data", "Fluid Levels", "Production"). These are visual dividers only — just work through each section in order.

Shift-Restricted Rows

Some rows may only be editable during a specific shift (AM or PM). If a row appears greyed out or unavailable, it may be restricted to a shift you are not currently working.

Calculated Fields

Your administrator may have configured calculations that auto-populate certain rows based on values you have already entered:

  • Calculated values appear automatically as you fill in related rows — you do not need to enter them manually
  • Some calculated rows are locked (read-only) to prevent accidental overrides — if you cannot enter a value, it is likely calculated
  • Calculations can reference values from your previous log entry — if a calculation seems off, check that you synced recently to ensure the previous log value is current on your device

Total Hours Rows

If your reading sheet has a Total Hours row, this tracks the cumulative lifetime runtime of the unit. Total hours values:

  • Can never decrease — only enter the current total hour reading; do not enter a lower number than what was previously logged
  • Drive preventative maintenance schedules — accurate total hours means schedules trigger at the right mileage/runtime
  • Are used by schedule calculations to automatically reset maintenance counters (e.g., oil hours) when a PM is completed

If you believe a total hours value is wrong, do not attempt to correct it yourself — contact your administrator. Incorrect total hours resets can affect schedule history and trigger unexpected maintenance events.

Out-of-Range Alerts

If you enter a value that falls below the manufacturer minimum or above the manufacturer maximum for a row, EZ Ops automatically sends an alert to the plant foreman. This happens on sync — you do not need to take any additional action, but be prepared to discuss the reading with your supervisor.

Completing the Log

Once you have entered all required readings, the log is saved and will sync with EZ Ops when you next connect. There is no separate "Submit" button for reading sheets — the data is captured as you enter it and uploaded on your next sync.

Common Issues

"I don't see the reading sheet for a piece of equipment"

  • Sync your device — new equipment or reading sheet updates require a sync to appear
  • Confirm with your administrator that the equipment is active and has a reading sheet configured

"A row is missing from the reading sheet"

  • Contact your administrator — rows are configured at the equipment level and must be added by an admin

"A calculated value looks wrong"

  • Double-check the values you entered that feed into the calculation
  • If you have not synced recently, calculations that reference the previous log entry may be using outdated data — sync and re-check
  • If it still seems incorrect, report it to your administrator to review the calculation setup

"The shift selection isn't appearing"

  • Your plant may not have shifts enabled — proceed without selecting a shift
  • If you believe it should be showing and isn't, contact your administrator

"I entered a total hours value incorrectly"

  • Contact your administrator immediately — do not attempt to correct it by entering a lower number

"A row won't let me type in it"

  • It may be a calculated row (read-only by design) or a shift-restricted row (only editable during a specific shift)
  • It may also be a dropdown row — look for a dropdown selector rather than a text field

Tips & Recommendations

  • Check total hours before moving on - Total hours drive maintenance schedules, so a mistyped figure can skip a PM or trigger one early.
  • Work down the sheet in order - Rows that feed a calculation have to be entered before the calculated row will populate correctly.
  • Sync once your log is complete - Readings stay on your device until you sync, and both schedules and supervisors work from synced data.
  • Select the correct shift first - Where shifts are enabled you cannot start a log without picking one, and the wrong shift can disable rows you need.
  • Log at consistent intervals - Time-based calculations and trend reporting lose most of their value when entries are irregular.